PORSCHE 986 ENGINE LIGHTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 - Fuel/Exhaust (includes uncategorized and accessory items) FVD111LAMVER Having problems with your check engine light? Want to run cat bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the dme (ecu)? This adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/co ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ecu! Use only for the 2nd oxygen sensor (after catalytic)! General FitmentBOXSTER 1997-04911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 911 1989-94 911 1987-89 911 1984-86 911 1978-83 CAYENNE 2007-10 CAYENNE 2003-06 CAYMAN 2006-08 BOXSTER 2005-08 968 1992-95 944 1982-85 944 1985-88 944 1989-91 928 1992-95 928 1987-91 928 1983-86 924 1986-88 924 1980-85 911 1994-98
$42.90
Make a selection 24135296401BS Highlights: superb daily driver, OEM replacement, r90 type approved pad. Features red "brake in" surface coating for instant safe braking after install. New 100 % eco friendly material with zero sulphides. No shims for noise reduction needed. More bite from cold. Works in hot and dry climates as well as in cold. Fully r 90 approved. If you simply need a quality OEM replacement pad, look no further than the blackstuff brake pad. It is a highly engineered brake compound that lasts longer, produces minimal dust and is the perfect choice for the urban or daily driver. Why spend more if all you need is a quality replacement pad? The blackstuff brake pad is a total non metallic pad containing zero steel fiber, maki...(choose a part on the right to read more)
$123.20
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,495.95
Make a selection 24135196401BS Highlights: superb daily driver, OEM replacement, r90 type approved pad. Features red "brake in" surface coating for instant safe braking after install. New 100 % eco friendly material with zero sulphides. No shims for noise reduction needed. More bite from cold. Works in hot and dry climates as well as in cold. Fully r 90 approved. If you simply need a quality OEM replacement pad, look no further than the blackstuff brake pad. It is a highly engineered brake compound that lasts longer, produces minimal dust and is the perfect choice for the urban or daily driver. Why spend more if all you need is a quality replacement pad? The blackstuff brake pad is a total non metallic pad containing zero steel fiber, maki...(choose a part on the right to read more)
$103.40
Make a selection 220110981001 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,479.50
Make a selection 24135291101BS If you simply need a quality OEM replacement pad, look no further than the blackstuff brake pad. It is a highly engineered brake compound that lasts longer, produces minimal dust and is the perfect choice for the urban or daily driver. Why spend more if all you need is a quality replacement pad? The blackstuff brake pad is a total non metallic pad containing zero steel fiber, making this a cleaner pad which is far less aggressive to cast iron brake rotors. Blackstuff has also been graded code "n" by the usa brake ratings system meaning this receives the top award for its environmentally friendly status and has also achieved the much coveted gg friction rating, almost unheard of in the automotive brake industr...(choose a part on the right to read more)
$97.90
Make a selection FVD11125101 Improve sound and performance at the track by decreasing exhaust backpressure with our GT2 evo style exhaust pipe. These also shed a ton of weight as they bypass the catalytics and muffler. + 25 crank hp gain. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany - weighs 2.2 lbs. (1.0 kg). Sold individually. 1 necessary per car. Please note: cat bypass pipes are not c.a.r.b. Certified (california) and are for racing use only. FVD is not responsible for emissions compliance. Engine management software must be updated to avoid a check engine light, purchase part # FVD99361891 or FVD99361890 General Fitment911 1994-98
From $468.60
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection BES99110200SK "brombacher" stainless steel exhaust system with valves for the 991 + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - under load (moving) with valves closed: 85db* - under load (movin...(choose a part on the right to read more)
$10,030.90
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 21011199309 Sport catalytic bypass- fits both bischoff and gillet systems General Fitment911 1994-98
$830.03
Make a selection BES987C0200SHD Brombacher Cayman/s (sound version) stainless steel exhaust system facts: - + 20 crank hp & + 19 crank torque - 200 cell high flow, tri metal German hjs sport catalysts - 2 tubing (50 mm) straight through design for max. Power - weighs 57 lbs. (25,8 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - dual 3.5 (90mm) round tips - includes quick release clamps - made in Germany - intoxicating growl at idle, partial throttle and wide open throttle - no dme programming necessary. FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredibl...(choose a part on the right to read more)
$8,541.03
Make a selection BES987C02F0S "brombacher" 987-2/s (sound version) stainless steel exhaust system
$7,420.60
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection BES97005080S11 Brombacher panamera s & 4s "sound version" sport muffler - 10 crank hp & + 9 crank torque. - 2.5'' tubing (63,5mm) straight through design for maximum power. - 11 lb. Weight savings. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - quad 4'' (100mm) round tips sold separately for basic OEM systems (without Porsche sport exhaust)* - tips can be individually adjusted for personal taste. - deeper tonal quality and louder volume which enhances 4.8 l Porsche sound.** - no ecu (software) programming necessary. - will work with OEM exhaust components. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - made in Germany...(choose a part on the right to read more)
$2,476.10
Make a selection 21011199313 Improve sound and performance by decreasing exhaust backpressure with our catalytic bypass kit. - + 18 crank hp & + 13 crank torque. - weighs 28 lbs. (13 kg). - t 304 stainless steel. - made in europe. - reduces thermal load on the heads. We recommend purchasing one our prepackaged installation kits, part # FVDmk993301 please note: cat bypass pipes are not c.a.r.b. Certified (california) and are for racing use only. FVD is not responsible for emissions compliance. Engine management software must be updated to avoid a check engine light, purchase part # FVD99361891 or FVD99361890. General Fitment911 1994-98
$3,371.18
Make a selection 21011199310 Improve sound and performance by decreasing exhaust backpressure with our sport catalytic kits. This kit utilizes high quality, 100 cell German cats. - + 16 crank hp & + 11 crank torque. - weighs 30 lbs. (13.7 kg). - t 304 stainless steel. - made in europe. - reduces thermal load on the heads. We recommend purchasing one our prepackaged installation kits, part # FVDmk993301 please note: 100 cell catalytic converters are not c.a.r.b. Certified (california). FVD is not responsible for emissions compliance. Engine management software must be updated to avoid a check engine light, purchase part # FVD99361891 or FVD99361890. General Fitment911 1994-98
From $3,000.07
Make a selection 22011098100 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,529.00
Make a selection FSPOR993TSPKGE Product details: General Fitment911 1994-98
From $7,750.00
Make a selection FSPOR992SC Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
$3,695.95
Make a selection BES99126010SOL Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel material. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs in the bumper perfectly can be adjusted for...(choose a part on the right to read more)
$660.00
Make a selection BES99126010S Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel material. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs in the bumper perfectly can be adjusted for...(choose a part on the right to read more)
$600.60
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,303.20
Make a selection BES99716000S1 Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs i...(choose a part on the right to read more)
$851.40
Make a selection BES99305040S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,820.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |